Rabbit of Caerbannog
(742 posts)
Send PM |
Profile |
Ignore
|
Fri Feb-20-04 02:59 PM
Original message |
|
Anyone ever BUILT a guitar (preferably accoustic). I do some wood working and have always thought of taking a whack at it. I'm certainly not short on tools (except for clamps. You can NEVER have too many clamps). I might even start with a kit, loke thos offered by Martin ( http://www.martinguitar.com/1833/catalog.php?cat=Kits%20Parts%20%26%20Tools&subcat=Kits) Any advice or suggestions?
|
ProfessorGAC
(1000+ posts)
Send PM |
Profile |
Ignore
|
Fri Feb-20-04 03:06 PM
Response to Original message |
1. Just A Safety Bit Of Advice |
|
I had a friend back in the late 70's who was a fully trained and certified luthier. He actually had contracts with Martin and Guild to do major repair work on vintage guitars, so he really knew his stuff.
If you're going to do any inlay work, have a fed air source and full face mask for sanding. He personally knew at least 3 guys with permanent respiratory conditions (severe), one of whom died at 35 years old, from getting the dust from abalone shell, mother of pearl, or ivory into their lungs.
He told me a dust mask is not good enough. The sanded particles are smaller than a virus, so they'll get through a dust mask. That stuff is really, really bad for you.
One other thing i remember. He said the back of an acoustic would only sound better if one bookmatched the bottom piece. Two pieces properly joined was supposed to create deeper resonance than a single piece back. I believed him, not only because he knew what he was talking about, but just about every really good acoustic i've ever played had a two piece back, and the cheapie Epiphones and Yamahas had one piece backs. So, i figured there was something to it.
BTW: He had 4 patents on bracing patterns, so it could be that his bracings had more to do with tone than anything else. He made one guitar that was a doubleneck acoustic (6 & 12) that he gave to Leo Kottke. Leo used it for about 6 years, and turned my friend on to Alvarez Yairi, who licensed his bracing design for 10 years at $150k. (That was in 1977, so that was a lot of dough!)
Can'g give you any more than that. The Professor
|
Dudley_DUright
(1000+ posts)
Send PM |
Profile |
Ignore
|
Fri Feb-20-04 03:13 PM
Response to Reply #1 |
2. It is definitely true that bracing patterns for acoustic guitars |
|
are absolutely critical on where the frequencies of the resonances occur. I have done some work on this in my acoustics lab. A kit would be a good way to start since the bracing pattern would be predetermined.
|
morningglory
(1000+ posts)
Send PM |
Profile |
Ignore
|
Fri Feb-20-04 04:07 PM
Response to Reply #1 |
3. Have to start with good wood, so I would get a kit from Martin |
|
or find a luthier who has some stock.
|
Rabbit of Caerbannog
(742 posts)
Send PM |
Profile |
Ignore
|
Fri Feb-20-04 04:12 PM
Response to Reply #3 |
5. I like the idea of the Martin. because it |
|
comes with everything pre bent and has everything except glue and finish. Another kit I'm looking at is from Stewart MacDonald: http://www.stewmac.com/shop/Kits/Acoustic_Guitar_Kits/Dreadnought_Guitar_Kits.html
|
Adams Wulff
(658 posts)
Send PM |
Profile |
Ignore
|
Fri Feb-20-04 04:12 PM
Response to Original message |
4. Maybe start with a dulcimer... |
|
Like this one: http://www.stewmac.com/shop/Kits/Dulcimer_Kits/Dulcimer_Kits.htmljust to get your feet wet, and to fire up your imagination. Thanks for that link, btw, I will be visiting there often!
|
Rabbit of Caerbannog
(742 posts)
Send PM |
Profile |
Ignore
|
Fri Feb-20-04 04:14 PM
Response to Reply #4 |
6. You read my mind and beat me to the post! |
|
I've already build a mountain dulcimer and a hammered, so - been there done that. Thanks
|
DU
AdBot (1000+ posts) |
Mon May 13th 2024, 05:11 PM
Response to Original message |